In here, the crystal and the circuitry responsible for temperature sensitivity have to be kept in a controlled structure. This ensures that it is in a stable condition of temperature, which should be higher than that ambient temperature necessary for exposing OCXO 10MHz Frequency Reference. In fact, it is better if the oven is set to turnover temperature of the resonators so that it balances with the external temperature.
Controlling the temperature will enable anomalies which are attached to temperature effects be minimized as much as possible. The anomalies can prove destructive to the resonators and may even allow compensation to a limited allowance. It could be possible to engage top overtone crystals to be used in control of temperatures. Being in controlled conditions make them better.
Stability can be enabled with these oscillators even more that it can be with those ones like SPXO and TXCO. These usually have no mechanisms for temperature control. The crystal units are the ones which determine the characteristics of the temperature. The oven controlled oscillator is rather better since the oven block is what maintains and controls the temperature as required.
It is the dynamic and static characteristics that bring about stability. Things like the accuracy of the oven, the resonator and even some other components are responsible for the kind of stability you can get. It is at a certain recommended range that this temperature stability can perform within. The narrow ranges are better placed as it allows restriction to the needed area.
The oven controlled oscillator needs more power in terms of consumption because it takes a long time to warm up. It is the kind of insulation used that majorly determines the power needed to be used for oven heating. If it is high, the heat usage will be reduced and this results in usage of less power.
It is the oven temperature that is set first to some higher degrees of temperature more than the normal ambient one. This is just to enable the oven have a good control in place. After this, is when you warm the resonator to attain some amount of heat up front. This is what caused equilibrium balancing.
If you want to minimize variations, then you have to carry out regulations. This is important so as to help reduce disturbances within the oscillator frequency. It is the difference in power that causes this to happen. If not dealt with, then it may go back to equilibrium.
The oscillator is quite sensitive to load and so you need to engage the functions of an amplifier to give multiple outputs. If built around the oven, then stability of the temperature will not interfere with it. It is better to check out on humidity so that you guard the stability.
Even if this may be the case, instability can be measured and can also be modelled in order to avert these temperature issues. There are also control mechanisms that can be used to control any error and avert instability. Such mechanisms can also help further by giving temperature compensation and effective aging. Additional characteristic series such as retrace can also be considered to avert such situations.
Controlling the temperature will enable anomalies which are attached to temperature effects be minimized as much as possible. The anomalies can prove destructive to the resonators and may even allow compensation to a limited allowance. It could be possible to engage top overtone crystals to be used in control of temperatures. Being in controlled conditions make them better.
Stability can be enabled with these oscillators even more that it can be with those ones like SPXO and TXCO. These usually have no mechanisms for temperature control. The crystal units are the ones which determine the characteristics of the temperature. The oven controlled oscillator is rather better since the oven block is what maintains and controls the temperature as required.
It is the dynamic and static characteristics that bring about stability. Things like the accuracy of the oven, the resonator and even some other components are responsible for the kind of stability you can get. It is at a certain recommended range that this temperature stability can perform within. The narrow ranges are better placed as it allows restriction to the needed area.
The oven controlled oscillator needs more power in terms of consumption because it takes a long time to warm up. It is the kind of insulation used that majorly determines the power needed to be used for oven heating. If it is high, the heat usage will be reduced and this results in usage of less power.
It is the oven temperature that is set first to some higher degrees of temperature more than the normal ambient one. This is just to enable the oven have a good control in place. After this, is when you warm the resonator to attain some amount of heat up front. This is what caused equilibrium balancing.
If you want to minimize variations, then you have to carry out regulations. This is important so as to help reduce disturbances within the oscillator frequency. It is the difference in power that causes this to happen. If not dealt with, then it may go back to equilibrium.
The oscillator is quite sensitive to load and so you need to engage the functions of an amplifier to give multiple outputs. If built around the oven, then stability of the temperature will not interfere with it. It is better to check out on humidity so that you guard the stability.
Even if this may be the case, instability can be measured and can also be modelled in order to avert these temperature issues. There are also control mechanisms that can be used to control any error and avert instability. Such mechanisms can also help further by giving temperature compensation and effective aging. Additional characteristic series such as retrace can also be considered to avert such situations.
No comments:
Post a Comment